|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
19-3562; Rev 1; 6/05 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers General Description The MAX5494-MAX5499 10-bit (1024-tap), dual, nonvolatile, linear-taper, programmable voltage-dividers and variable resistors perform the function of a mechanical potentiometer, but replace the mechanics with a 3-wire SPITM-compatible serial interface. The MAX5494/MAX5495 are dual, 3-terminal, programmable voltage-dividers; the MAX5496/MAX5497 are dual, 2-terminal variable resistors; and the MAX5498/ MAX5499 include one 2-terminal variable resistor and one 3-terminal programmable voltage-divider. The MAX5494-MAX5499 feature an internal, nonvolatile, electrically erasable programmable read-only memory (EEPROM) that stores the wiper position for initialization during power-up. The 3-wire SPI-compatible serial interface allows communication at data rates up to 7MHz. The MAX5494-MAX5499 are ideal for applications requiring digitally controlled potentiometers. End-to-end resistance values of 10k and 50k are available with a 35ppm/C end-to-end temperature coefficient. The ratiometric temperature coefficient is 5ppm/C for each channel, making these devices ideal for applications requiring low-temperature-coefficient programmable voltagedividers such as low-drift, programmable-gain amplifiers. The MAX5494-MAX5499 operate with either a single power supply (+2.7V to +5.25V) or dual power supplies (2.5V). The devices consume 400A (max) of supply current when writing data to the nonvolatile memory and 1.5A (max) of standby supply current. The devices are available in space-saving (5mm x 5mm x 0.8mm), 16-pin TQFN package and are specified over the extended (-40C to +85C) temperature range. Features Wiper Position Stored in Nonvolatile Memory and Recalled Upon Power-Up 16-Pin, 5mm x 5mm x 0.8mm TQFN Package 35ppm/C End-to-End Resistance Temperature Coefficient 5ppm/C Ratiometric Temperature Coefficient 10k and 50k End-to-End Resistor Values 3-Wire SPI-Compatible Serial Interface Reliability (TA = +85C) 50,000 Wiper Store Cycles 50 Years Wiper Data Retention 1.5A (max) Standby Current Single +2.7V to +5.25V Supply Operation Dual 2.5V Supply Operation MAX5494-MAX5499 Pin Configurations GND W1 TOP VIEW 12 DIN 13 N.C. 14 N.C. 15 SCLK 16 1 CS INTERFACE 11 10 H1 9 8 7 VSS N.C. N.C. VDD MAX5494 MAX5495 L1 6 5 W2 N.C. 14 N.C. 15 INTERFACE Gain and Offset Adjustment LCD Contrast Adjustment Pressure Sensors Low-Drift Programmable-Gain Amplifiers Mechanical Potentiometer Replacement Volume Control 5mm x 5mm x 0.8mm TQFN D.N.C. 9 8 7 VSS N.C. N.C. VDD GND W1 L1 10 12 DIN 13 11 Ordering Information PART MAX5494ETE MAX5495ETE TEMP RANGE PINPACKAGE PKG CODE T1655-2 T1655-2 SCLK 16 MAX5496 MAX5497 H2 L2 Applications 2 3 4 6 5 -40C to +85C 16 TQFN-EP* -40C to +85C 16 TQFN-EP* 1 CS 2 W2 3 L2 4 D.N.C. *EP = Exposed pad. Ordering Information continued at end of data sheet. Selector Guide appears at end of data sheet. SPI is a trademark of Motorola, Inc. 5mm x 5mm x 0.8mm TQFN Pin Configurations continued at end of data sheet. 1 ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers MAX5494-MAX5499 ABSOLUTE MAXIMUM RATINGS VDD to GND ...........................................................-0.3V to +6.0V VSS to GND............................................................-6.0V to +0.3V VDD to VSS .............................................................-0.3V to +6.0V H1, H2, L1, L2, W1, W2 to VSS.........(VSS - 0.3V) to (VDD + 0.3V) CS, SCLK, DIN to GND ..............................-0.3V to (VDD + 0.3V) Maximum Continuous Current into H_, L_, and W_ MAX5494/MAX5496/MAX5498 ....................................5.0mA MAX5495/MAX5497/MAX5499 ....................................1.0mA Maximum Current Into Other Pins .................................50.0mA Continuous Power Dissipation (TA = +70C) 16-Pin TQFN (derate 20.8mW/C above +70C) ....1666.7mW Operating Temperature Range ...........................-40C to +85C Junction Temperature ......................................................+150C Storage Temperature Range .............................-60C to +150C Lead Temperature (soldering, 10s) .................................+300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VDD = +2.7V to +5.25V, VSS = GND = 0, VH_ = VDD, VL_ = 0, TA = -40C to +85C, unless otherwise noted. Typical values are at VDD = +5.0V, TA = +25C.) (Note 1) PARAMETER Resolution Integral Nonlinearity (Note 2) Differential Nonlinearity (Note 2) End-to-End Resistance Temperature Coefficient Ratiometric Temperature Coefficient Full-Scale Error Zero-Scale Error Wiper Capacitance End-to-End Resistance Channel-to-Channel Division Ratio Matching FSE ZSE CW RHL MAX5494/MAX5498 MAX5495/MAX5499 VDD = 3V, midcode: 512 MAX5494 MAX5495 7.5 37.5 MAX5494/MAX5498 MAX5495/MAX5499 MAX5494/MAX5498 MAX5495/MAX5499 -4 -4 0 0 SYMBOL N INL DNL TCR VDD = 2.7V VDD = 5V VDD = 2.7V VDD = 5V 35 5 -2.5 -0.75 3.3 1.45 60 10 50 0.05 0.15 6.3 k MAX5495/MAX5499, W_ at 15 code, H_ and L_ shorted to VSS, measure resistance from W_ to H_ (Figures 4 and 5) 25 12.5 62.5 0 0 5 5 CONDITIONS MIN 10 2 2 1 1 TYP MAX UNITS Bits LSB LSB ppm/C ppm/C LSB LSB pF k % DC PERFORMANCE (MAX5494/MAX5495/MAX5498/MAX5499 Programmable Voltage-Divider) MAX5494/MAX5498, W_ at 15 code, H_ and L_ shorted to VSS, measure resistance from W_ to H_ (Figures 4 and 5) Resistance from W_ to L_ and H_ 2 _______________________________________________________________________________________ 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers ELECTRICAL CHARACTERISTICS (continued) (VDD = +2.7V to +5.25V, VSS = GND = 0, VH_ = VDD, VL_ = 0, TA = -40C to +85C, unless otherwise noted. Typical values are at VDD = +5.0V, TA = +25C.) (Note 1) PARAMETER Resolution Integral Nonlinearity (Note 3) SYMBOL N VDD = 2.7V INL_R VDD = 3V VDD = 5V VDD = 2.7V Differential Nonlinearity (Note 3) Variable-Resistor Temperature Coefficient Wiper Resistance Wiper Capacitance Full-Scale Wiper-to-End Resistance Zero-Scale Resistor Error DNL_R VDD = 3V VDD = 5V TCVR RW CWR RW-L RZ MAX5496/MAX5498 MAX5497/MAX5499 Code = 0 MAX5494/MAX5498 MAX5495/MAX5499 MAX5496/MAX5498, Code >128 VDD = 3V to 5.25V MAX5497/MAX5499, Code >200 7.5 37.5 VDD = 3V to 5.25V; code = 128 to 1024 VDD 3V (Note 4) -1 -1 -4 -4 CONDITIONS MIN 10 -1.6 -1.4 -1.3 +0.45 +0.4 +0.35 35 50 60 10 50 70 110 0.1 % 0.15 12.5 62.5 +1 +1 ppm/C pF k LSB +4 +4 LSB TYP MAX UNITS Bits DC PERFORMANCE (MAX5496-MAX5499 Variable Resistor) MAX5494-MAX5499 Two-Channel Resistance Matching DIGITAL INPUTS (CS, SCLK, DIN) (Note 5) Single-supply operation Input High Voltage VIH Dual-supply operation Single-supply operation Input Low Voltage VIL Dual-supply operation VDD = 3.6V to 5.25V VDD = 2.7V to 3.6V With respect to GND, VDD = 2.5V, VSS = -2.5V VDD = 2.7V to 5.25V With respect to GND, VDD = 2.5V, VSS = -2.5V 2.4 0.7 x VDD 2.0 V 0.8 V 0.6 1 5 A pF Input Leakage Current Input Capacitance DYNAMIC CHARACTERISTICS Wiper -3dB Bandwidth IIN CIN Wiper at code 495 (01111 01111), 10pF load at wiper MAX5494/MAX5498 MAX5495/MAX5499 250 kHz 50 BW _______________________________________________________________________________________ 3 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers MAX5494-MAX5499 ELECTRICAL CHARACTERISTICS (continued) (VDD = +2.7V to +5.25V, VSS = GND = 0, VH_ = VDD, VL_ = 0, TA = -40C to +85C, unless otherwise noted. Typical values are at VDD = +5.0V, TA = +25C.) (Note 1) PARAMETER SYMBOL CONDITIONS MAX5494/MAX5498; VDD = 3V; wiper at code 495; 10kHz, 1VRMS signal is applied at H_; 10pF load at wiper Total Harmonic Distortion THD MAX5495/MAX5499; VDD = 3V; wiper at code 495; 10kHz, 1VRMS signal is applied at H_; 10pF load at wiper CH2 = 11111 11111, CH1 = 01111 01111, CW_ = 10pF, VH1 = VDD = +2.5V, VL1 = VSS = -2.5V, measure VW1 with VW2 = 5VP-P at f = 1kHz 0.03 MIN TYP 0.026 % MAX UNITS Analog Crosstalk -93 dB NONVOLATILE MEMORY RELIABILITY Data Retention Endurance POWER SUPPLIES Single-Supply Voltage Dual-Supply Voltage Average Programming Current Peak Programming Current Standby Current IDD VDD VDD VSS IPG VSS = GND = 0 GND = 0 (VDD - VSS) 5.25V During nonvolatile write only; digital inputs = VDD or GND During nonvolatile write only; digital inputs = VDD or GND Digital inputs = VDD or GND, TA = +25C 2.70 2.50 -2.5 220 4 0.6 1.5 5.25 5.25 -0.2 400 V V A mA A TA = +85C TA = +25C TA = +85C 50 200,000 50,000 Years Stores 4 _______________________________________________________________________________________ 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers TIMING CHARACTERISTICS (VDD = +2.7V to +5.25V, VSS = GND = 0, VH_ = VDD, VL_ = 0, TA = -40C to +85C, unless otherwise noted. Typical values are at VDD = +5.0V, TA = +25C.) (Note 1) PARAMETER ANALOG SECTION Wiper Settling Time (Note 6) tS MAX5494/MAX5498 MAX5495/MAX5499 5 22 7 140 60 60 60 0 40 0 15 60 150 12 s SYMBOL CONDITIONS MIN TYP MAX UNITS MAX5494-MAX5499 SPI-COMPATIBLE SERIAL INTERFACE (Figure 6) SCLK Frequency SCLK Clock Period SCLK Pulse-Width High SCLK Pulse-Width Low CS Fall to SCLK Rise Setup SCLK Rise to CS Rise Hold DIN to SCLK Setup DIN Hold After SCLK SCLK Rise to CS Fall Delay CS Rise to SCLK Rise Hold CS Pulse-Width High Write NV Register Busy Time fSCLK tCP tCH tCL tCSS tCSH tDS tDH tCS0 tCS1 tCSW tBUSY MHz ns ns ns ns ns ns ns ns ns ns ms Note 1: 100% production tested at TA = +25C and TA = +85C. Guaranteed by design to TA = -40C. Note 2: The DNL and INL are measured for the voltage-divider with H_ = VDD and L_ = VSS. The wiper terminal (W_) is unloaded and measured with a high-input-impedance voltmeter. Note 3: The DNL and INL are measured with L_ = VSS = 0. For VDD = 5V, the wiper terminal is driven with a current source of IW = 80A for the 50k device and IW = 400A for the 10k device. For VDD = 3V, the wiper terminal is driven with a current source of IW = 40A for the 50k device and IW = 200A for the 10k device. Note 4: The wiper resistance is measured using the source currents given in Note 3. Note 5: The device draws higher supply current when the digital inputs are driven with voltages between (VDD - 0.5V) and (GND + 0.5V). See the Supply Current vs. Digital Input Voltage graph in the Typical Operating Characteristics. Note 6: Wiper settling test condition uses the voltage-divider with a 10pF load on W_. Transition code from 0 to 495 and measure the time from CS going high to the wiper voltage settling to within 0.5% of its final value. _______________________________________________________________________________________ 5 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers MAX5494-MAX5499 Typical Operating Characteristics (VDD = +5.0V, VSS = 0, TA = +25C, unless otherwise noted.) DIFFERENTIAL NONLINEARITY vs. CODE (VARIABLE RESISTOR) MAX5494 toc01 INTEGRAL NONLINEARITY vs. CODE (VARIABLE RESISTOR) MAX5494 toc02 MAXIMUM DIFFERENTIAL NONLINEARITY vs. SUPPLY VOLTAGE (VARIABLE RESISTOR) 0.8 0.6 0.4 DNL (LSB) 0.2 0 -0.2 -0.4 -0.6 -0.8 MAX5494 toc03 1.0 0.8 0.6 0.4 DNL (LSB) VDD = 3V 1.5 VDD = 3V 1.0 0.5 INL (LSB) 0 -0.5 -1.0 -1.5 1.0 0.2 0 -0.2 -0.4 -0.6 -0.8 -1.0 0 128 256 384 512 640 768 896 1024 CODE -1.0 0 128 256 384 512 640 768 896 1024 CODE 2.5 3.0 3.5 4.0 4.5 5.0 VDD (V) MAXIMUM INTEGRAL NONLINEARITY vs. SUPPLY VOLTAGE (VARIABLE RESISTOR) MAX5494 toc04 DIFFERENTIAL NONLINEARITY vs. CODE (VOLTAGE-DIVIDER) MAX5494 toc05 INTEGRAL NONLINEARITY vs. CODE (VOLTAGE-DIVIDER) VDD = 3V 1.0 0.5 INL (LSB) 0 -0.5 -1.0 -1.5 MAX5494 toc06 1.0 0.5 0 -0.5 -1.0 -1.5 -2.0 2.5 3.0 3.5 4.0 4.5 1.0 0.8 0.6 0.4 DNL (LSB) 0.2 0 -0.2 -0.4 -0.6 -0.8 -1.0 VDD = 3V 1.5 INL (LSB) 5.0 0 128 256 384 512 640 768 896 1024 CODE 0 128 256 384 512 640 768 896 1024 CODE VDD (V) WIPER RESISTANCE vs. CODE (VARIABLE RESISTOR) 70 60 40 RWL (k) 40 30 20 10 10 0 0 128 256 384 512 640 768 896 1024 CODE 0 0 30 20 MAX5494 toc07 END-TO-END RESISTANCE vs. CODE (MAX5497/MAX5499) MAX5494 toc08 END-TO-END RESISTANCE vs. CODE (MAX5496/MAX5498) MAX5494 toc09 80 60 50 12 10 8 RWL (k) 6 4 2 0 50 RW () 128 256 384 512 640 768 896 1024 CODE 0 128 256 384 512 640 768 896 1024 CODE 6 _______________________________________________________________________________________ 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers MAX5494-MAX5499 Typical Operating Characteristics (continued) (VDD = +5.0V, VSS = 0, TA = +25C, unless otherwise noted.) WIPER RESISTANCE vs. WIPER VOLTAGE (VARIABLE RESISTOR) MAX5494 toc10 END-TO-END RESISTANCE (RHL) % CHANGE vs. TEMPERATURE (VOLTAGE-DIVIDER) MAX5494 toc11 WIPER-TO-END RESISTANCE (RWL) % CHANGE vs. TEMPERATURE (VARIABLE RESISTOR) WIPER-TO-END RESISTANCE CHANGE (%) 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1.0 -40 -15 10 35 60 85 CODE IS 11 1111 1111 MAX5494 toc12 22 CODE IS 00 0000 0000 21 20 RW () 19 18 17 16 0 1 2 3 4 5 WIPER VOLTAGE (V) VDD = 5V 1.0 END-TO-END RESISTANCE CHANGE (%) 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1.0 -40 -15 10 35 60 1.0 85 TEMPERATURE (C) TEMPERATURE (C) STANDBY SUPPLY CURRENT vs. TEMPERATURE MAX5494 toc13 DIGITAL SUPPLY CURRENT vs. DIGITAL INPUT VOLTAGE MAX5494 toc14 RATIOMETRIC TEMPERATURE COEFFICIENT vs. CODE 180 RATIOMETRIC TEMPCO (ppm/C) 160 140 120 100 80 60 40 20 10k 50k VOLTAGE-DIVIDER VDD = 3V TA = -40C TO +85C MAX5494 toc15 1.5 VDD = 5.25V 10,000 200 VDD = 5V 1.2 1000 IDD (A) 0.6 IDD (A) 0.9 100 10 0.3 1 0 -40 -15 10 35 60 85 TEMPERATURE (C) 0.1 0 1 2 3 4 5 DIGITAL INPUT VOLTAGE (V) 0 0 128 256 384 512 640 768 896 1024 CODE VARIABLE RESISTOR TEMPERATURE COEFFICIENT vs. CODE MAX5494 toc16 TAP-TO-TAP SWITCHING TRANSIENT (MAX5494/MAX5498) MAX5494 toc17 TAP-TO-TAP SWITCHING TRANSIENT (MAX5495/MAX5499) CS 2V/div MAX5494 toc18 700 600 500 TCVR (ppm/C) 400 300 200 50k 100 0 0 10k VDD = 3V TA = -40C TO +85C CS 2V/div VW_ 20mV/div H_ = VDD L_ = GND FROM CODE 01111 11111 TO CODE 10000 00000 CW_ = 10pF 1s/div H_ = VDD L_ = GND FROM CODE 01111 11111 TO CODE 10000 00000 CW_ = 10pF 4s/div VW_ 20mV/div 128 256 384 512 640 768 896 1024 CODE _______________________________________________________________________________________ 7 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers MAX5494-MAX5499 Typical Operating Characteristics (continued) (VDD = +5.0V, VSS = 0, TA = +25C, unless otherwise noted.) CROSSTALK MAX5494 toc19 CROSSTALK vs. FREQUENCY CW_ = 10pF CODE = 01111 01111 -20 CROSSTALK (dB) -40 -60 -80 -100 -120 MAX5494 toc20 VW2 2V/div 0 VW1 20mV/div VH2 = VDD VL2 = VL1 = VH1 = GND CW_ = 10pF 400ns/div MAX5494/MAX5498 MAX5495/MAX5499 0.01 0.1 1 10 100 1000 FREQUENCY (kHz) THD+N vs. FREQUENCY (MAX5494/MAX5498) CW_ = 10pF CODE = 01111 01111 MAX5494 toc21 THD+N vs. FREQUENCY (MAX5495/MAX5499) CW_ = 10pF CODE = 01111 01111 1 MAX5494 toc22 10 10 1 THD+N (%) THD+N (%) 0.1 0.1 0.01 0.01 0.001 0.001 0.0001 0.01 0.1 1 FREQUENCY (kHz) 10 100 0.0001 0.01 0.1 1 FREQUENCY (kHz) 10 100 WIPER RESPONSE vs. FREQUENCY (MAX5494/MAX5498) MAX5494 toc23 WIPER RESPONSE vs. FREQUENCY (MAX5495/MAX5499) MAX5494 toc24 0 CW_ = 10pF 0 -5 -5 CW_ = 10pF GAIN (dB) CW_ = 30pF -15 GAIN (dB) -10 -10 CW_ = 30pF -15 -20 CODE = 01111 01111 0.1 1 10 FREQUENCY (kHz) 100 1000 -20 CODE = 01111 01111 0.1 1 10 FREQUENCY (kHz) 100 1000 -25 -25 8 _______________________________________________________________________________________ 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers Pin Descriptions PIN MAX5494/ MAX5495 1 2 3 4 5 6, 7,14,15 MAX5496/ MAX5497 1 2 3 -- 5 6, 7,14,15 MAX5498/ MAX5499 1 2 3 -- 5 6, 7,14,15 NAME FUNCTION Active-Low Chip-Select Input. Drive CS low to enable the serial interface. Drive CS high to disable the serial interface and put the device in standby mode. Wiper Terminal 2 Low Terminal 2 High Terminal 2 Positive Power-Supply Input. 2.7V VDD 5.25V. Bypass with a 0.1F capacitor from VDD to GND as close to the device as possible No Connection. Not internally connected. Negative Power-Supply Input. Single-supply operation: VSS = GND = 0. Dual-supply operation: -2.5V VSS -0.2V (VSS can vary as long as (VDD - VSS) 5.25V). Bypass with a 0.1F capacitor from VSS to GND as close to the device as possible. High Terminal 1 Low Terminal 1 Wiper Terminal 1 Ground Serial-Data Input. The data at DIN synchronously loads into the serial shift register on each SCLK rising edge. Serial-Clock Input . SCLK clocks in the data when CS is low. Do Not Connect. Leave unconnected for proper operation. Exposed Pad. Externally connect EP to VSS to provide a low thermal resistance path from the IC junction to the PC board or leave unconnected. MAX5494-MAX5499 CS W2 L2 H2 VDD N.C. 8 8 8 VSS 9 10 11 12 13 16 -- EP -- 10 11 12 13 16 4, 9 EP 9 10 11 12 13 16 4 EP H1 L1 W1 GND DIN SCLK D.N.C Exposed Pad _______________________________________________________________________________________ 9 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers MAX5494-MAX5499 Functional Diagrams H1 VDD GND VSS POR SPI INTERFACE 2 x 10 BIT NVM 10-BIT LATCH 10 DECODER 1024 TAPS W1 CS SCLK DIN 10-BIT LATCH 10 L1 H2 MAX5494 MAX5495 DECODER 1024 TAPS W2 L2 NOTE: THE PROGRAMMABLE VOLTAGE-DIVIDER IS NOT INTENDED FOR CURRENT TO FLOW THROUGH THE WIPER. NOTE: SEE THE MAX5494/MAX5495/MAX5498/MAX5499 PROGRAMMABLE VOLTAGE-DIVIDERS SECTION. Figure 1. MAX5494/MAX5495 Functional Diagram 10 ______________________________________________________________________________________ 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers Functional Diagrams (continued) MAX5494-MAX5499 VDD GND VSS POR SPI INTERFACE 2 x 10 BIT NVM 10-BIT LATCH 10 DECODER 1024 TAPS W1 L1 CS SCLK DIN 10-BIT LATCH 10 DECODER 1024 TAPS W2 MAX5496 MAX5497 L2 Figure 2. MAX5496/MAX5497 Functional Diagram H1 VDD GND VSS POR SPI INTERFACE 2 x 10 BIT NVM 10-BIT LATCH 10 DECODER 1024 TAPS W1 CS SCLK DIN 10-BIT LATCH 10 L1 MAX5498 MAX5499 DECODER 1024 TAPS W2 L2 NOTE: THE PROGRAMMABLE VOLTAGE-DIVIDER IS NOT INTENDED FOR CURRENT TO FLOW THROUGH THE WIPER. NOTE: SEE THE MAX5494/MAX5495/MAX5498/MAX5499 PROGRAMMABLE VOLTAGE-DIVIDERS SECTION. Figure 3. MAX5498/MAX5499 Functional Diagram ______________________________________________________________________________________ 11 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers MAX5494-MAX5499 Detailed Description The MAX5494-MAX5499 dual, nonvolatile, linear-taper, programmable voltage-dividers and variable resistors feature 1024 tap points (10-bit resolution) (see the Functional Diagrams). These devices consist of multiple strings of equal resistor segments with a wiper contact that moves among the 1024 effective tap points by a 3-wire SPI-compatible serial interface. The MAX5494/MAX5496/MAX5498 provide a total 10k end-to-end resistance, and the MAX5495/MAX5497/ MAX5499 feature a 50k end-to-end resistance. The MAX5494/MAX5495/MAX5498/MAX5499 allow access to the high, low, and wiper terminals for a standard voltage-divider configuration. Ensure that the terminal voltages fall between VSS and VDD. VHL - (| VFSE | + | VZSE |) D + VL + | VZSE | 1023 where D is the decimal equivalent of the 10 data bits written (0 to 1023), VHL is the voltage difference between the H_ and L_ terminals, and: V VFSE = FSE HL 1024 V VZSE = ZSE HL 1024 The MAX5494/MAX5498 provide a 10k end-to-end resistance value, while the MAX5495/MAX5499 feature a 50k end-to-end resistance value. Note that the programmable voltage-divider is not intended to be used as a variable resistor. Wiper current creates a nonlinear voltage drop in series with the wiper. To ensure temperature drift remains within specifications, do not pull current through the voltage-divider wiper. Connect the wiper to a high-impedance node. Figures 4 and 5 show the behavior of the programmable voltage-divider resistance from W_ to H_ and W_ to L_, respectively. This does not apply to the variable-resistor devices. MAX5494/MAX5495/MAX5498/MAX5499 Programmable Voltage-Dividers The MAX5494/MAX5495/MAX5498/MAX5499 programmable voltage-dividers provide a weighted average of the voltage between the H_ and L_ inputs at the W_ output. The MAX5494/MAX5495/MAX5498/MAX5499 programmable voltage-divider network provides up to 1024 division ratios between the H_ and L_ voltage. Ideally, the VL voltage occurs at the wiper terminal when all data bits are zeros and the VH voltage occurs at the wiper terminal when all data bits are one (see the wiper voltage equation). The step-size voltage (1 LSB) is equal to the voltage applied across terminals H and L divided by 210. Calculate the wiper voltage VW as follows: MAX5496-MAX5499 Variable Resistors The MAX5496-MAX5499 provide a programmable resistance from W_ to L_. The MAX5496/MAX5498 provide a 10k end-to-end resistance value, while the MAX5497/MAX5499 feature a 50k end-to-end resistance value. The programmable resolution of this 18 16 14 12 RW_H_ (k) 10 8 6 4 2 0 0 128 256 384 512 640 768 896 1024 CODE (DECIMAL) 50k SCALES BY A FACTOR OF FIVE RW_L_ (k) 18 16 14 12 10 8 6 4 2 0 0 128 256 384 512 640 768 896 1024 CODE (DECIMAL) 50k SCALES BY A FACTOR OF FIVE Figure 4. Resistance from W_ to H_ vs. Code (10k VoltageDivider) 12 Figure 5. Resistance from W_ to L_ vs. Code (10k VoltageDivider) ______________________________________________________________________________________ 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers resistance is equal to the nominal end-to-end resistance divided by 1024 (10-bit resolution). For example, the programmable resolution is 9.8 and 48.8 for the MAX5496/MAX5498 and the MAX5497/MAX5499, respectively. The 10-bit data in the 10-bit latch register selects the wiper position from the 1024 possible positions, resulting in 1024 values for the resistance from W_ to L_. Calculate the resistance from W_ to L_ (RWL) from the formula below: D RWL (D) = x RW-L + RZ 1023 where D is decimal equivalent of the 10 data bits written, RW-L is the nominal end-to-end resistance, and RZ is the zero-scale error. Table 1 shows RWL at selected codes. either eight clock cycles to transfer the command bits (Figure 7b) or 24 clock cycles with 16 bits disregarded by the device (Figure 7a). After the loading of data into the shift register, drive CS high to latch the data into the appropriate control register (specified by RA1 and RA0) and disable the serial interface. Keep CS low during the entire serial data stream to avoid corruption of the data. Table 2 shows the register map. Write Wiper Register The "write wiper register" command (C1, C0 = 00) controls the wiper positions. The 10 data bits (D9-D0) indicate the position of the wiper. For example, if DIN = 000000 0000, the wiper moves to the position closest to L_. If DIN = 11 1111 1111, the wiper moves closest to H_. MAX5494-MAX5499 Table 1. RWL at Selected Codes END-TO-END RESISTANCE VALUE CODE (DECIMAL) 0 1 512 1023 10k RWL () 70 80 5,070 10,070 50k RWL () 110 160 25,110 50,110 SPI-Compatible Serial Interface The MAX5494-MAX5499 use a 3-wire, SPI-compatible, serial data interface (Figure 6). This write-only interface contains three inputs: chip-select (CS), data input (DIN), and data clock (SCLK). Drive CS low to enable the serial interface and clock data synchronously into the shift register on each SCLK rising edge. The WRITE commands (C1, C0 = 00 or 01) require 24 clock cycles to transfer the command and data (Figure 7a). The COPY commands (C1, C0 = 10 or 11) use CS tCSS tCSO SCLK tCL tCH tCP tCSH tCSW tCS1 tDS DIN tDH Figure 6. SPI-Interface Timing Diagram ______________________________________________________________________________________ 13 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers MAX5494-MAX5499 a) 24-BIT COMMAND/DATA WORD CS SCLK 1 DIN 2 3 4 5 6 7 8 9 10 D8 11 D7 12 D6 13 D5 14 D4 15 D3 16 D2 17 D1 18 D0 19 20 21 22 23 24 C1 C0 RA1 RA0 D9 b) 8-BIT COMMAND WORD CS SCLK 1 DIN 2 3 4 5 6 7 8 C1 C0 RA1 RA0 Figure 7. SPI-Compatible Serial-Interface Format Table 2. Register Map* CLOCK EDGE Bit Name Write Wiper Register 1 Write Wiper Register 2 Write NV Register 1 Write NV Register 2 Copy Wiper Register 1 to NV Register 1 Copy Wiper Register 2 to NV Register 2 Copy Wiper Register 1 to NV Register 1 and Copy Wiper Register 2 to NV Register 2 Simultaneously Copy NV Register 1 to Wiper Register 1 Copy NV Register 2 to Wiper Register 2 Copy NV Register 1 to Wiper Register 1 and Copy NV Register 2 to Wiper Register 2 Simultaneously 1 -- 0 0 0 0 0 0 2 -- 0 0 0 0 0 0 3 C1 0 0 0 0 1 1 4 C0 0 0 1 1 0 0 5 -- 0 0 0 0 0 0 6 -- 0 0 0 0 0 0 7 0 1 0 1 0 1 8 1 0 1 0 1 0 9 D9 D9 D9 D9 D9 -- -- 10 D8 D8 D8 D8 D8 -- -- 11 D7 D7 D7 D7 D7 -- -- 12 D6 D6 D6 D6 D6 -- -- 13 D5 D5 D5 D5 D5 -- -- 14 D4 D4 D4 D4 D4 -- -- 15 D3 D3 D3 D3 D3 -- -- 16 D2 D2 D2 D2 D2 -- -- 17 D1 D1 D1 D1 D1 -- -- 18 D0 D0 D0 D0 D0 -- -- ... -- -- -- -- -- -- -- 24 -- -- -- -- -- -- -- RA1 RA0 0 0 1 0 0 0 1 1 -- -- -- -- -- -- -- -- -- -- -- -- 0 0 0 0 1 1 1 1 0 0 0 0 0 1 1 0 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0 0 1 1 0 0 1 1 -- -- -- -- -- -- -- -- -- -- -- -- *D9 is the MSB and D0 is the LSB of the data bits. 14 ______________________________________________________________________________________ 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers The "write wiper register" command writes data to the volatile random access memory (RAM), leaving the NV registers unchanged. When the device powers up, the data stored in the NV registers transfers to the wiper register, moving the wiper to the stored position. Figure 8 shows how to write data to wiper register 1. Write NV Register The "write NV register" command (C1, C0 = 01) stores the position of the wiper to the NV registers for use at power-up. Alternatively, the "copy wiper register to NV register" command writes to the NV register. Writing to the NV register does not affect the position of the wipers. The operation takes up to 12ms (max) after CS goes high to complete and no other operation should be performed until completion. Figure 9 shows how to write data to the NV register 1. Copy Wiper Register to NV Register The "copy wiper register to NV register" command (C1, C0 = 10) stores the current position of the wiper to the NV register for use at power-up. Figure 10 shows how to copy data from wiper register 1 to NV register 1. MAX5494-MAX5499 CS 1 SCLK 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 C1 C0 DIN 0 0 0 0 0 0 RA1 RA0 0 1 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 X X X X X X ACTION WIPER REGISTER 1 UPDATED Figure 8. Write Wiper Register 1 CS 1 SCLK 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 C1 C0 DIN 0 0 0 1 0 0 RA1 RA0 0 1 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 X X X X X X tBUSY WRITE NV REGISTER 1 (DEVICE IS BUSY) ACTION Figure 9. Write NV Register 1 ______________________________________________________________________________________ 15 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers MAX5494-MAX5499 Copy NV Register to Wiper Register The "copy NV register to wiper register" (C1, C0 = 11) restores the wiper position to the current value stored in the NV register. Figure 11 shows how to copy data from NV register 1 to wiper register 1. the factory. The nonvolatile memory is guaranteed for 50 years for wiper data retention and up to 200,000 wiper write cycles. Power-Up Upon power-up, the MAX5494-MAX5499 load the data stored in the nonvolatile wiper register into the wiper register, updating the wiper position with the data stored in the nonvolatile wiper register. Standby Mode The MAX5494-MAX5499 feature a low-power standby mode. When the device is not being programmed, it enters into standby mode and supply current drops to 0.6A (typ). Applications Information The MAX5494-MAX5499 are intended for circuits requiring digitally controlled adjustable resistance, such as LCD contrast control (where voltage biasing adjusts the display contrast), or programmable filters with adjustable gain and/or cutoff frequency. Nonvolatile Memory The internal EEPROM consists of a nonvolatile register that retains the last value stored prior to power-down. The nonvolatile register is programmed to midscale at CS CS 1 SCLK 2 3 4 5 6 7 8 SCLK 1 2 3 4 5 6 7 8 C1 DIN 0 0 1 C0 0 0 0 RA1 0 RA0 1 DIN 0 0 C1 1 C0 1 0 0 RA1 0 RA0 1 tBUSY WRITE NV REGISTER 1 (DEVICE IS BUSY) WIPER REGISTER 1 UPDATED ACTION ACTION Figure 10. Copy Wiper Register 1 to NV Register 1 Figure 11. Copy NV Register 1 to Wiper Register 1 16 ______________________________________________________________________________________ 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers Positive LCD Bias Control Figures 12 and 13 show an application where the voltage-divider or variable resistor is used to make an adjustable, positive LCD-bias voltage. The op amp provides buffering and gain to the resistor-divider network. MAX5494-MAX5499 R1 R2 1 fC = 2 x R3 x C G = 1+ Programmable Filter Figure 14 shows the configuration for a 1st-order programmable filter. The gain of the filter is adjusted by R2, and the cutoff frequency is adjusted by R3. Use the following equations to calculate the gain (G) and the 3dB cutoff frequency (fC). Gain and Offset Voltage Adjustment Figure 15 shows an application using the MAX5498/ MAX5499 to adjust the gain and nullify the offset voltage. 5V H_ 30V 1/2 MAX5494/MAX5495 1/2 MAX5498/MAX5499 L_ 1/2 MAX5496-MAX5499 W_ MAX480 5V 30V VOUT MAX480 VOUT W_ L_ Figure 12. Positive LCD Bias Control Using a Voltage-Divider Figure 13. Positive LCD Bias Control Using a Variable Resistor C VIN VOUT 1/2 MAX5498/MAX5499 1/2 MAX5496-MAX5499 R3 W_ L_ R1 VREF H_ W_ L_ VOUT 1/2 MAX5496-MAX5499 R2 W_ L_ 1/2 MAX5498/MAX5499 W_ VIN L_ Figure 14. Programmable Filter Figure 15. Gain- and Offset-Voltage Adjustment Circuit ______________________________________________________________________________________ 17 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers MAX5494-MAX5499 Selector Guide PART CONFIGURATION Two programmable voltagedividers Two programmable voltagedividers Two variable resistors Two variable resistors One programmable voltagedivider and one variable resistor One programmable voltagedivider and one variable resistor END-TO-END RESISTANCE (k) 10 50 10 50 10 50 Ordering Information (continued) PART MAX5496ETE MAX5497ETE MAX5498ETE MAX5499ETE TEMP RANGE PINPACKAGE PKG CODE T1655-2 T1655-2 T1655-2 T1655-2 -40C to +85C 16 TQFN-EP* -40C to +85C 16 TQFN-EP* -40C to +85C 16 TQFN-EP* -40C to +85C 16 TQFN-EP* MAX5494ETE MAX5495ETE MAX5496ETE MAX5497ETE MAX5498ETE MAX5499ETE *EP = Exposed pad. Chip Information TRANSISTOR COUNT: 32,262 PROCESS: BiCMOS Pin Configurations (continued) TOP VIEW GND W1 H1 9 8 INTERFACE 7 VSS N.C. N.C. VDD L1 10 12 DIN 13 N.C. 14 N.C. 15 SCLK 16 1 CS 11 MAX5498 MAX5499 6 5 2 W2 3 L2 4 D.N.C. 5mm x 5mm x 0.8mm TQFN 18 ______________________________________________________________________________________ 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) QFN THIN.EPS MAX5494-MAX5499 D2 D D/2 MARKING k L E/2 E2/2 E (NE-1) X e C L C L b D2/2 0.10 M C A B XXXXX E2 PIN # 1 I.D. DETAIL A e (ND-1) X e e/2 PIN # 1 I.D. 0.35x45 DETAIL B e L1 L C L C L L L e 0.10 C A 0.08 C e C A1 A3 PACKAGE OUTLINE, 16, 20, 28, 32, 40L THIN QFN, 5x5x0.8mm -DRAWING NOT TO SCALE- 21-0140 H 1 2 ______________________________________________________________________________________ 19 10-Bit, Dual, Nonvolatile, Linear-Taper Digital Potentiometers MAX5494-MAX5499 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) COMMON DIMENSIONS PKG. 16L 5x5 20L 5x5 28L 5x5 32L 5x5 40L 5x5 SYMBOL MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. EXPOSED PAD VARIATIONS PKG. CODES T1655-1 T1655-2 T1655N-1 T2055-2 T2055-3 T2055-4 T2055-5 T2855-1 T2855-2 T2855-3 T2855-4 T2855-5 T2855-6 T2855-7 T2855-8 T2855N-1 T3255-2 T3255-3 T3255-4 T3255N-1 T4055-1 D2 MIN. NOM. MAX. MIN. E2 NOM. MAX. L 0.15 A A1 A3 b D E e k L L1 N ND NE JEDEC NOTES: DOWN BONDS ALLOWED 0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80 0 0.02 0.05 0 0.02 0.05 0 0.02 0.05 0.20 REF. 0.20 0.25 0.30 4.90 5.00 5.10 4.90 5.00 5.10 0.50 BSC. 0.25 0 0.02 0.05 0.20 REF. 0.20 0.25 0.30 4.90 5.00 5.10 4.90 5.00 5.10 0.50 BSC. 0.25 0 0.02 0.05 0.20 REF. 0.20 REF. 0.25 0.30 0.35 0.25 0.30 0.35 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 0.80 BSC. 0.65 BSC. 0.25 - 0.25 0.20 REF. 0.15 0.20 0.25 4.90 5.00 5.10 4.90 5.00 5.10 0.40 BSC. 0.25 0.35 0.45 3.00 3.00 3.00 3.00 3.00 3.00 3.15 3.15 2.60 3.15 2.60 2.60 3.15 2.60 3.15 3.15 3.00 3.00 3.00 3.00 3.20 3.10 3.20 3.00 3.10 3.20 3.00 3.10 3.20 3.00 3.10 3.20 3.00 3.10 3.20 3.00 3.10 3.20 3.00 3.25 3.25 2.70 3.25 2.70 2.70 3.25 2.70 3.25 3.25 3.10 3.10 3.10 3.10 3.35 3.35 2.80 3.35 2.80 2.80 3.35 2.80 3.35 3.35 3.20 3.20 3.20 3.20 3.15 3.15 2.60 3.15 2.60 2.60 3.15 2.60 3.15 3.15 3.00 3.00 3.00 3.00 3.10 3.10 3.10 3.10 3.10 3.10 3.25 3.25 2.70 3.25 2.70 2.70 3.25 2.70 3.25 3.25 3.10 3.10 3.10 3.10 3.30 3.20 3.20 3.20 3.20 3.20 3.20 3.35 3.35 2.80 3.35 2.80 2.80 3.35 2.80 3.35 3.35 3.20 3.20 3.20 3.20 3.40 ** ** ** ** ** ** 0.40 ** ** ** ** ** ** ** 0.40 ** ** ** ** ** ** NO YES NO NO YES NO YES NO NO YES YES NO NO YES YES NO NO YES NO NO YES 0.30 0.40 0.50 0.45 0.55 0.65 0.45 0.55 0.65 0.30 0.40 0.50 0.40 0.50 0.60 - 0.30 0.40 0.50 16 20 28 32 40 4 5 7 8 10 4 5 7 8 10 WHHB WHHC WHHD-1 WHHD-2 ----- 1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994. 2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES. 3. N IS THE TOTAL NUMBER OF TERMINALS. 4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO JESD 95-1 SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE TERMINAL #1 IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE. 5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.25 mm AND 0.30 mm FROM TERMINAL TIP. 6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY. 7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION. 8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS. 9. DRAWING CONFORMS TO JEDEC MO220, EXCEPT EXPOSED PAD DIMENSION FOR T2855-1, T2855-3, AND T2855-6. 10. WARPAGE SHALL NOT EXCEED 0.10 mm. 11. MARKING IS FOR PACKAGE ORIENTATION REFERENCE ONLY. 12. NUMBER OF LEADS SHOWN ARE FOR REFERENCE ONLY. 13. LEAD CENTERLINES TO BE AT TRUE POSITION AS DEFINED BY BASIC DIMENSION "e", 0.05. 3.30 3.40 3.20 ** SEE COMMON DIMENSIONS TABLE PACKAGE OUTLINE, 16, 20, 28, 32, 40L THIN QFN, 5x5x0.8mm -DRAWING NOT TO SCALE- 21-0140 H 2 2 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 20 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2005 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products, Inc. |
Price & Availability of MAX5495ETE |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |